Home / 3D Printing Processes / Papergraphics 3D Prints Larger than Life Greek Statue with Massivit 1800

Papergraphics 3D Prints Larger than Life Greek Statue with Massivit 1800

The low cost of materials and extremely high speed of the Massivit 1800 3D printer is inspiring some of the company’s new distributor to experiment with its capabilities. Since the system is targeted primarily at the visual marketing industry, many of its current customers and resellers are used to larger than life prints. Except now they are larger than life 3D prints and what better subject than a Greek god to demonstrate it?

Papergraphics took on distribution of the Massivit 3D printers in 2016. The UK company exhibited the Massivit 3D printer at a recent show in the Netherlands using this as an opportunity to create their own giant 3D models. When 3D printing with the Massivit 1800 (and in general) you need to plan for support angles, structural strength, joining points, and finishing. Using this information, the Massivit software will convert it into layers for printing.

The finished statue has a completed height of 3,400 mm. The Massivit printer can print a single piece 1,800 mm high (that’s close to two meters), 1,500mm wide and 1,200mm deep.

“We printed in sections comprising of legs, torso, head, hands, robe edge and shield, says Graham De Kock, Technical & Service Manager at Papergraphics. “This allowed more structureless printing which is quicker, easier to handle and finish. The largest single component on this model being 1,600 mm tall.”

Physical printing time was approximately 42 hours for all parts, which is significantly quicker than any other 3D printing technology. Assembly and finishing took 6 days. Some reverse angles required printing of support pillars or posts. These were cut off post printing. Any remaining hole was filled with Dimengel, the Acrylic polymer gel that the model is made up of, using a UV torch to cure the gel. The benefit is it cures immediately and it is strong.

The team sprayed on 3 coats of car filler with a spray gun to smooth out the layers that make up the structure sanding between coats. Where they noted slightly deeper grooves or imperfections they used Dimengel or applied a part body filler and then sanded it. They went on to create a steel base to support the model, attaching two L shaped steel beams as the central support structure. The 1st runs from the models foot to shoulder and the 2nd runs from the the other foot to waist height. These beams were bolted to the base so that they could later be unbolted for transport.

“We commit to offering the highest level of service, training and support” says Graham DeKock, “to truly offer this we undertake the type of project that we would expect our customers to produce, thus equipping us with the advanced skills, knowledge and know how required.”

To assemble the components, the team placed the legs over the supporting beams, then filled them with polyurethane expanding foam. The mixture foams up inside the model, providing added strength and bonding the model shell to the internal posts. It is important to not add too much polyurethane at a time as heat is generated and expanding forces are applied within the shell of the model.

We then cleaned the next surfaces that were to be joined. In this instance it was the waist of the model and the base of the torso and used a two part superglue to fix them together. Once glued we filled any gaps with Dimengel and then continued filling with Polyurethane, being careful to use a single batch to fill the joined area for added strength. We repeated this process in joining the hands, robe and finally the head. It is necessary to cut holes above some join points, ie in the arm, to allow you to pour in the polyurethane, and then use the cut out piece to refill the hole and then smooth over with Dimengel.

Once all joins were completed they applied an undercoat to the model to check for imperfections and then sanded and filled these. Finally, they applied 2 coats of a textured spray paint to give the model its final, highly realistic, stone appearance.

 

About 3D Printing Media Network

Check Also

METROPOLE 3D Prints Life Size Corto Maltese for 50th Anniversary of Comic Book Series

Paris-based sign and display company, METROPOLE, 3D printed this life-size replica of the much-loved Corto …

Leave a Reply

Your email address will not be published. Required fields are marked *